Tectonic uplift can be defined as the portion of the total geologic uplift of the mean earth surface that is not attributable to an isostatic response to unloading. Isostatic response is important and will be discussed in this article; however, an increase in the mean elevation of a region can only occur in response to tectonic processes of crustal thickening (such as mountain building events), changes in the density distribution of the crust and underlying mantle, and flexural support due to the bending of rigid lithosphere. It is also good to take into consideration the effects of denudation (processes that wear away the earth's surface). Within the scope of this topic, uplift relates to denudation in that denudation brings buried rocks closer to the surface. This process can redistribute large loads from an elevated region to a topographically lower area as well – thus promoting isostatic response in the region of denudation (which can cause local bedrock uplift). The timing, magnitude, and rate of denudation can be estimated using pressure-temperature studies.
Crustal thickening has an upward component of motion and often occurs when continental crust is thrust onto continental crust. Basically nappes (thrust sheets) from each plate collide and begin to stack one on top of the other; evidence of this process can be seen in preserved ophiolitic nappes (preserved in the Himalaya), and in rocks with an inverted metamorphic gradient. The preserved inverted metamorphic gradient indicates that nappes were actually stacked on top of each other so quickly, that hot rocks did not have time to equilibrate before being thrust on top of cool rocks. The process of nappe stacking can only continue for so long, as gravity will eventually disallow further vertical growth (there is an upper limit to vertical mountain growth).
Although the raised surfaces of mountain ranges mainly result from crustal thickening, there are other forces at play that are responsible for tectonic activity. All tectonic processes are driven by gravitational force when density differences are present. A good example of this would be the large-scale circulation of the mantle (which plate tectonics is a part of). Lateral density variations near the surface (such as the creation, cooling, and subduction of oceanic plates) also drive plate motion. The dynamics of mountain ranges are governed by differences in the gravitational potential energy of entire “columns” of lithosphere (see Isostacy). If a change in surface height represents an isostatically compensated change in crustal thickness, the rate of change of potential energy per unit surface area is proportional to the rate of increase of average surface height. The highest rates of working against gravity are required when the thickness of the crust (not the lithosphere) changes (England and Molnar, 1990).
Orogenic uplift is the result of tectonic-plate collisions and results in mountain ranges or a more modest uplift over a large region. Perhaps the most extreme form of orogenic uplift is a continental-continental crustal collision. In this process, two continents are sutured together and large mountain ranges are produced. The collision of the Indian and Eurasian plates is a good example of the extent to which orogenic uplift can reach. Heavy thrust faulting (of the Indian plate beneath the Eurasian plate) and folding are responsible for the suturing together of the two plates. The collision of the Indian and Eurasian plates not only produced the Himalaya, but is also responsible for crustal thickening up into Siberia. The Pamir Mountains, Tian Shan, Altai, Hindu Kush, and other mountain belts are all examples of mountain ranges formed in response to the collision of the Indian with the Eurasian plate. . Deformation of continental lithosphere can take place in several possible modes, and there are quite a few theories around.
The Ozark Plateau is a broad uplifted area which resulted from the Permian Ouachita Orogeny to the south in the states of Arkansas, Oklahoma and Texas. Another related uplift is the Llano Uplift in Texas, a geographical location named after its uplift features.
The removal of mass from a region will be isostatically compensated by crustal rebound. If we take into consideration typical crustal and mantle densities, erosion of an average 100 meters of rock across a broad, uniform surface will cause the crust to isostatically rebound ~85 meters and will cause only a 15 meter loss of mean surface elevation. An example of isostatic uplift would be post-glacial rebound following the melting of continental glaciers and ice sheets. The Hudson Bay region of Canada,the Great Lakes of Canada, and the United States are currently undergoing gradual rebound as a result of the melting of ice sheets 10,000 years ago.
Crustal thickening, which for example is currently occurring in the Himalaya due to the continental collision between the Indian Plate and the Eurasian Plate, can also lead to surface uplift; but due to the isostatic sinking of thickened crust, the magnitude of surface uplift will only be about one-sixth of the amount of crustal thickening. Therefore, in most convergent settings isostatic uplift plays a relatively small role and high peak formation can be more attributed to tectonic processes . Direct measures of the elevation change of the land surface can only be used to estimate erosion or bedrock uplift rates when other controls (such as changes in mean surface elevation, volume of eroded material, time scales and lags of isostatic response, variations in crustal density) are known.
In a few cases, tectonic uplift can be seen in the cases of coral islands. This is evidenced by the presence of various oceanic islands composed entirely of coral, which otherwise appear to be high islands (i.e., islands of volcanic origin). Examples of such islands are found in the Pacific, notably the three phosphate islets, Nauru, Makatea, and Banaba as well as Maré and Lifou in New-Caledonia, Fatu Huku in the Marquesas Islands and Henderson Island in the Pitcairn Islands. The uplift of these islands is the result of the movement of oceanic tectonic plates. Sunken islands or guyots with their coral reefs are the result of crustal subsidence as the oceanic plate carries the islands to deeper or lower oceanic crust areas.
The word “uplift” refers to displacement contrary to the direction of the gravity vector, and displacement is only defined when the object being displaced and the frame of reference are specified. According to Molnar and England (1990), there are three kinds of displacement to which the term “uplift” is applied: 1. Displacement of the Earth's surface with respect to the geoid. This is what we refer to as “surface uplift”; and surface uplift can be defined by averaging elevation and changes in elevation over surface areas of a specified size. 2. The “uplift of rocks” refers to the displacement of rocks with respect to the geoid. Lastly, the displacement of rocks with respect to the surface is called “exhumation”. This simple equation relates the three kinds of displacement:
Surface uplift = uplift of rock - exhumation
The term geoid is used above to mean “mean sea level”, and makes a good frame of reference. A given displacement within this frame of reference allows one to quantify the amount of work being done against gravity. Measuring uplift and exhumation can be tricky. Measuring the uplift of a point requires measuring its elevation change – usually geoscientists are not trying to determine what the uplift of a singular point is, but rather what the uplift over an area is. So, the change in elevation of all points on the surface of that area must be measured, and the rate of erosion must be zero or minimal. Also, sequences of rocks deposited during that uplift must be preserved. Needless to say, in mountain ranges where elevations are far above sea level these criteria are not always easily met. Paleoclimatic restorations though can be very valuable; these studies involve inferring changes in climate in an area of interest from changes with time of flora/fauna that are known to be sensitive to temperature and rainfall. The magnitude of the exhumation a rock has been subjected to may be inferred from geobarometry (measuring previous pressure and temperature history of a rock or assemblage). Knowing the pressure and temperature history of a region can yield an estimate of the ambient geothermal gradient and bounds on the exhumation process; however, geobarometric/geothermometric studies do not produce a rate of exhumation (or any other information on time). This is not too much of a problem anymore though, as exhumation rates can be inferred from fission tracks and radiometric ages as long as one has an estimated thermal profile.
Here you can share your comments or contribute with more information, content, resources or links about this topic.